Part number: HUC101212CSS600 — decoded, with sibling variants and the warranty check.
Before you buy: this is a SAS drive
SAS drives do not plug into a normal SATA motherboard port. You need a SAS host bus adapter or a backplane that speaks SAS - an LSI/Broadcom HBA in IT mode is the usual answer. A SATA drive will run on a SAS controller, but not the other way round. HBA and IT-mode guide
This is a refurbished or recertified listing
Recertified enterprise drives are pulled from datacentre fleets, tested and resold. They are usually the cheapest route to bulk capacity, and the risk is concentrated in the first weeks - so check SMART data the day it arrives rather than the day you need it. What recertified means · Refurbished warranty terms · Verify on arrival
The HGST 1.2TB 10K SAS 12G 2.5 is a 1.2TB 10K RPM SAS drive at $44.17/TB - double the random IOPS of 7200 RPM nearline. Best for OLTP and virtualization where NVMe budget is constrained.
Against every other drive we have an in-stock price for today, this one is cheaper per tb than 35% of them (85 of 241). The cheapest we can currently buy is $14.99/TB; the middle of the market is $38.12/TB.
These are third-party figures about the retail market as a whole, quoted and dated. They are not our own measurements and they do not describe this specific drive.
Yes. At our last check it was $53.00 ($44.17 per terabyte at its 1.2TB capacity), sold used under ASIN B07XR6KDQ4. Amazon sets the final price at checkout.
Amazon reports this listing (HUC101212CSS600) as used, and its title makes no renewed or recertified claim, so the unit's origin is whatever the seller's note says - shown beside the price.
Use Case Scenarios
🏠
Home & SMB NAS
Building a mid-range NAS for media, backups and file sharing.
~ Good fit
Verify CMR recording before using in RAID. Refurb units offer strong value for non-critical NAS.
💾
Backup Server / Veeam Target
Dedicated backup storage for Veeam, Commvault, or NetBackup.
✓ Excellent fit
1.2TB SAS drives are ideal for backup targets. Dual-port SAS suits dual-path backup infrastructure.
🏦
Performance-Sensitive OLTP
10K RPM SAS for databases needing better IOPS without NVMe cost.
✓ Excellent fit
10K RPM delivers ~300 IOPS vs ~150 for 7200 RPM — double the random performance at a fraction of SSD cost. Use RAID 10 for optimal performance.
Maintenance & Troubleshooting
Maintenance Checklist
On installCheck SMART baseline on arrival
Run smartctl -a /dev/sdX and record: Reallocated_Sector_Ct, Power_On_Hours, Spin_Retry_Count. Critical for refurb drives — refuse any with reallocated sectors > 0.
MonthlyRun SMART short self-test
smartctl -t short /dev/sdX — takes 1-2 minutes, catches most developing issues. Schedule during off-peak.
QuarterlyRun SMART long self-test
smartctl -t long /dev/sdX — full surface scan, takes 1 hours for 1.2TB. Any test failure is grounds for immediate replacement.
QuarterlyCheck RAID array health
Verify no degraded drives. A degraded array with no hot spare is one failure from data loss. Check mdstat or controller UI.
AnnuallyVerify drive firmware version
Check HGST support site for firmware updates. Some versions have known bugs affecting integrity.
Every 3-5 yearsPlan proactive replacement
Enterprise HDDs have higher failure rates after year 4-5. At 1.2TB per drive, budget for replacements before failures occur.
Troubleshooting Guide
Cause: HBA not initialized, SAS expander issue, cable fault, or incompatible controller.
Fix: Verify HBA firmware. Check SAS topology with sas2ircu or StorCLI. Test with known-good cable. Confirm drive is SAS not SATA.