ProLiant DL380 Gen10 Buyer's Guide - Parts & Prices

Every configuration, with its own table: ProLiant DL380 Gen10 drive compatibility

Memory that fits, cheapest per gigabyte

Full compatibility list and population rules: memory for the DL380 Gen10 · memory finder

What the ProLiant DL380 Gen10 is, and where it sits

The ProLiant DL380 Gen10 is a 2U rack HPE ProLiant machine built on the Intel Xeon Scalable (1st / 2nd generation) platform, and it belongs to HPE's Gen10 line. It reached the second-hand market the way all enterprise hardware does: in bulk, at the end of a lease or a refresh cycle, from organisations that bought it new for a great deal of money and now want it off the floor. That is the whole reason it is interesting to a homelab or a small office. You are not buying a cheap server. You are buying an expensive server late.

What makes this particular machine worth a page is its storage. In its 12 x 3.5in LFF configuration it carries 12 front bays, and across every configuration HPE documents it tops out at 24. Bays are the thing a used server gives you that a desktop or a small NAS cannot, and they are the reason people put a two-decade-old-sounding machine in a cupboard and run it for years. A 24-bay chassis with a SAS backplane will accept cheap SATA capacity drives, and that combination — enterprise chassis, consumer drive prices — is the entire economic case.

It is also worth being clear about what you are taking on. This is rack hardware designed for a room with its own cooling and its own acoustics budget, and it was designed by people who assumed nobody would ever have to sleep near it. The four sections below cover the four things that actually catch buyers out — noise, power, the storage controller, and remote-management licensing — and none of them are reasons not to buy. They are reasons to know what you are buying.

Which one of these should you actually buy?

HPE sold several machines in this family and the used market carries all of them at once, often at overlapping prices, which is how people end up with the wrong one. The short version for the ProLiant DL380 Gen10: it is a 2U machine, which is where the drive bays are. If you want density in a short rack, the 1U siblings are cheaper but carry far fewer disks. Compare it against ProLiant DL380 Gen9.

The four things that catch people out

1. Noise

ProLiant rack fans behave much like their Dell equivalents: quiet enough in a rack, loud enough to notice in a room. The recurring trigger reported by owners is a third-party PCIe card or drive that iLO cannot identify, which raises the fan floor. Community fan-control approaches exist and are documented on ServeTheHome and r/homelab. We do not reproduce them here — they are unofficial and firmware-dependent. No decibel or idle-wattage figure appears on this page because we have not measured one.

The practical buying advice that follows from this is simple and does not require any unofficial tinkering: think about where the machine will live before you think about which one to buy. A garage, a basement, a proper rack in a room you do not work in — any of those, and this is a non-issue. A cupboard off a bedroom, and it is the thing you will regret. That decision costs nothing to make now and is expensive to reverse once a 70-pound chassis is in the house.

2. Power

Power is the cost people forget to price, and unlike the purchase it repeats every month. A dual-socket machine of this generation idles at a level that is a real line on a household bill, and it does that whether or not you are using it. We do not publish an idle-wattage figure for the ProLiant DL380 Gen10, because we have not measured one and HPE does not state one for a used configuration — the number depends on which processors are fitted, how many DIMMs are populated, how many drives are spinning and which power supplies are installed. Anyone quoting you a single confident watt figure for “an ProLiant DL380 Gen10” is quoting a machine, not the machine you are buying.

What you can do is price it properly before you commit. Take your electricity rate, multiply by 24 and by 365, and apply it to a range rather than a point — then decide whether the answer changes your mind. For most people running one machine it does not. For people planning to run three, it usually does, and that is exactly the calculation that should happen before the purchase rather than after the first bill. Our calculators cover the storage side of the same question.

3. The storage controller, and whether it will run ZFS

ProLiant machines of this generation ship with Smart Array controllers. A Smart Array in RAID mode presents logical drives rather than raw disks, which is not what ZFS wants. HPE's documentation for this generation lists HBA-mode-capable controllers alongside the Smart Array family. As with the Dell equivalents, buy the controller you want rather than planning to change it, and settle the question before purchase.

The full explanation, and which specific cards ship ready versus needing a firmware change, is on our IT mode guide — and the card decoder lists every controller we track with live prices.

This matters more than any other single specification if you intend to run TrueNAS, Proxmox with ZFS, Unraid or anything else that wants to manage disks itself. Those systems want to see each physical drive, read its SMART data and handle redundancy in software. A RAID controller in its normal mode hides all of that behind virtual disks, and the failure mode is not a crash — it is that everything appears to work while your filesystem is blind to the health of the hardware underneath it. Settle this question with the seller before money changes hands, because it is a much cheaper question to ask than to answer later.

4. Remote management licensing

iLO 5 keeps the same split: a free Standard tier, with the Integrated Remote Console and virtual media in the licensed tiers (Advanced and above). Ask the seller which licence, if any, is active on the specific machine you are buying.

The reason this deserves its own section rather than a footnote is that remote management is most of the point of enterprise hardware for a home user. A machine you can power-cycle, reinstall and rescue from a laptop is a machine that can live somewhere inconvenient. A machine without that is one you will be carrying a monitor and keyboard to. The hardware is present either way; what varies is the licence, and the licence is not visible in a listing photograph.

Choosing the configuration before you choose the seller

The ProLiant DL380 Gen10 is available in configurations that take 3.5" drives, which is what you want if capacity per pound is the goal. Large-capacity spinning disks are only sold in that form factor, and no adapter meaningfully changes that in a hot-swap bay — a caddy that lets a 2.5" drive sit in a 3.5" bay exists, but the reverse does not.

Some configurations of this machine carry NVMe bays. Those bays take U.2 or U.3 enterprise drives, not the M.2 sticks a desktop uses — the connector, the power envelope and the physical carrier are all different, and an M.2 drive cannot be made to fit a hot-swap NVMe bay with an adapter you would want in a server. Check which specific configuration a listing is before you buy drives for it.

Right now our catalogue carries 20 in-stock 3.5" drives and 16 in-stock 2.5" drives that fit machines of this class. The full breakdown, config by config, is on the ProLiant DL380 Gen10 drive compatibility page.

Complete builds and comparisons

We have no complete build guide on this specific machine yet, but the build guides on its siblings translate directly, and the build calculator will price this model with your own configuration.

Weighing it against another machine: ProLiant DL380 Gen9 vs ProLiant DL380 Gen10. And to price a configuration of your own, the build calculator opens preselected on this model.

Verifying one on arrival

Used enterprise hardware is generally sound — it was built to a standard a desktop is not, and most of it has spent its life in a temperature-controlled room. But it arrives without a warranty conversation, so the first hour matters. Work through this before the return window closes rather than before the first weekend project:

• It POSTs, and it POSTs clean. Not just “it turns on” — watch the whole power-on self test and read any amber lights or panel codes rather than assuming they clear.
• Every bay detects a drive. Move one known-good drive through all 12 bays if you have to. A dead backplane channel is invisible until the day you fill the chassis, and it is not a repair you want to discover six months in.
• Remote management is reachable, and you know its tier. Get to the login page, get in, and then try the remote console specifically — that is the feature that sits behind the licence.
• Both power supplies are present and both work. Pull one at a time under load. Redundancy you have not tested is not redundancy, and sellers frequently ship these with one live PSU and one blank.
• Count the caddies. Drive carriers are sold separately, they are model-specific, and a “24-bay” machine that arrives with two caddies is a machine you will spend real money finishing.
• Check the memory the system actually sees against what the listing claimed, in the management interface rather than in the operating system.

Apply the same discipline to any drives that came with it. Bundled disks in a used server are usually the drives the previous owner had least reason to keep, and they arrive with an unknown number of powered-on hours. Our guide to recertified and refurbished drives covers what to check and what the numbers mean, and it applies to bundled drives exactly as it applies to bought ones. The full first-hour procedure is on verify on arrival, and the licensing question above is covered in depth on iDRAC and iLO licensing.

Caddies and carriers

Drive carriers are specific to a chassis generation and form factor, and they are not interchangeable across generations even within one vendor's line. We do not publish carrier part numbers for the ProLiant DL380 Gen10. The reason is deliberate: HPE's own documentation for this machine describes carriers generically and does not list part numbers, and the numbers that circulate on forums are frequently right for one generation and wrong for the next. A wrong caddy is a real cost and a genuinely annoying return. Buy carriers matched to the specific model and form factor, from a seller who states which generation they fit, and where you can, buy the machine with its caddies already in it — a chassis that arrives fully populated with carriers is worth paying a premium for.

Live prices for the carriers this machine takes, including the multi-packs that make filling a chassis affordable, are on our HPE Gen10 carrier page, alongside the compatibility list and what to check when they arrive.